100 Backup has encountered a serious error in List Manager. Quit and restart Backup, and then try again.
101 Backup is unable to open the error log file on your hard drive. There may not be enough space on your disk. To view the error log file, you can open the file ERROR.LOG in the LOG subdirectory wherever your Backup files are located.
102 Serious error.
103 Backup has encountered a serious error in List Manager. Quit and restart Backup, and then try again.
105 Either the source is empty, or no files have been selected. Select the files or folders you want to use for this operation, and then try again.
107 Unexpected exit during execution. Quit and restart Backup, and then try again.
108 The source tape you requested is not available. If you are sure you have inserted the correct tape, quit Backup and all running programs, restart Backup, and then try again.
109 There is not enough memory available for Backup to run reliably. Quit one or more programs, and then try again.
110 Backup encountered a file error in list global memory. Quit Backup and all running programs, restart Backup, and then try again.
111 Backup cannot find the specified file.
112 The operation could not proceed. For more information, see the error log.
113 The operation could not proceed. Quit and restart Backup, and then try again.
114 Serious error.
115 Serious error.
116 The volume you specified does not exist on this tape. \nInsert the tape that contains this volume, and then try again.
117 Some critical files may not have been restored.
118 One or more users are still logged on to the network drive.
119 The file you specified was not found. Make sure you have specified the filename correctly, and then try again.
120 Backup could not detect a tape drive. Try redetecting the drive by double-clicking the 'Add New Hardware' icon in Control Panel, and then clicking 'Automatically detect installed hardware' on the second screen. If the problem persists, check the connections to the drive, or contact the hardware vendor.
121 The tape in the drive is not the one you specified in your request. Insert the correct tape, and then try again.
122 Insert a tape in the selected drive, and then try again.
123 Backup has encountered a serious error in the Memory Manager.
143 Backup has encountered a serious error in its Tape Manager. Quit Backup and all other running programs, restart Backup, and then try again.
144 There is no tape in the selected drive.
145 Unexpected end of data on tape.
146 Backup cannot read the directory for this volume. The data in this volume is not retrievable. Other volumes on this tape may be usable. Possible causes:\n\n- Unerasing a volume whose data was already overwritten.\n- Creating a volume with software other than Backup.
147 Tape header contains unexpected or invalid values.
148 Backup encountered an error reading this tape. This error may be caused by an unformatted or incorrectly formatted tape. Reformat the tape, and then try again.
149 The volume table contains unexpected or invalid values. The tape you are using is in a format that is incompatible with Backup.
150 This directory contains data that is either corrupted or a size mismatch.
151 Backup cannot read the data in this directory. The data on this tape is not retrievable. Other volumes on this tape may be usable. Possible causes:\n\n- Unerasing a volume whose data was already overwritten.\n- Creating a volume with software other than Backup.
152 This tape is incompatible with the tape drive.
153 The data on this tape cannot be retrieved. The tape you are using is in a format that is incompatible with Backup.
154 System resources are not available.
155 Either the system has insufficient resources or some other process is using the resources that Backup needs. Quit one or more programs, and then try again. If that doesn't work, quit Backup and all other running programs, restart Windows, and then try again.
156 Tape is not the first tape in series.
157 This tape is part of a volume that spans two or more tapes, and it is not the first in the series. Insert the first tape or disk in the series, and then try again.
158 The volume number you specified does not exist on this tape.
159 Tape or disk in drive is not the one identified in request.
160 The tape or disk currently in the drive is not the one identified in your request. Remove it and insert the originally requested tape or disk. The new information will appear in approximately 30 seconds.
161 Backup has encountered an invalid timer ID. Quit Backup and all running programs, restart Backup, and then try again.
162 The tape currently in the drive is not formatted. Format the tape, or insert a formatted tape, and then try again.
164 This volume spans several tapes, and the current tape is not the last in the series. To see complete directory information, return to the previous screen by pressing the Previous Step button and then insert the last tape in the series. The current tape includes a directory only for files up to and including this tape.
167 Tape contains excessive errors.
168 This tape is reporting the maximum number of allowable operations or errors. Try using a cleaning cartridge to clean the tape drive head. If the problem persists, save any data you want from the tape by transferring it to a different tape. If you want to be able to write to this tape, you need to reformat it.
169 Backup has encountered a serious error in Task Manager. Quit Backup and all running programs, restart Backup, and then try again.
170 This operation is attempting to exceed the system resource limit. Quit Backup and all running programs, restart Backup, and then try again. If the problem persists, try shutting down and restarting Windows, and then try again.
171 Backup has encountered a locked resource. Quit Backup and all running programs, restart Backup, and then try again.
172 Backup could not find the virtual device driver named QIC117.VXD that it needs to run.
173 Backup has detected an incompatible version of the virtual device driver named QIC117.VSD that it needs to run. Reinstall Backup, and then try again. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
174 Backup cannot find an interrupt setting it needs. Reinstall Backup, and then try again. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
208 Backup has encountered an unknown program error. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
209 Backup has attempted to use a locked resource. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
210 The volume you specified is not on the current tape. Insert a different tape, and then try again.
211 Too many bad sectors.
212 More than 5% of the sectors on this tape are unreadable. Possible solutions:\n\n1. Clean the tape drive head with a cartridge cleaner.\n2. Try using a different tape; this one may be worn.\n3. Make sure the tape drive is properly grounded.
213 Backup has encountered an unknown program error. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
214 Volume table is full.
215 You have reached the maximum number of volumes that can fit on a tape.\nYou can erase this tape, or use a different one.
216 This drive can not decompress data.
217 Error writing to tape.
218 Backup encountered an error while writing to this tape. The current backup is unusable.\nHowever, previous backups are still valid. Before you can use this tape to store more data, you need to reformat it.
219 Unformatted segment error.
220 This tape has not been completely formatted. Reformat this tape, and then try again.
221 Error correction attempt failed.
222 Backup was unable to reconstruct the files. Possible solutions:\n\n1. Clean the tape drive head.\n2. Make sure the tape drive is properly grounded.\nIf the problem persists, contact the hardware vendor.
223 This tape drive is incompatible with Backup.
224 Backup has encountered a serious error in Compression Manager. Quit Backup and all other running programs, restart Backup, and then try again.
225 Compression DMA communication failure.
226 The file BACKUP.CFG is missing or corrupted. You need to reinstall Backup. To do this, look up 'Add/Remove Programs' in the Windows Help Index.
227 Backup was unable to access the specified file. Quit and restart Backup, and then try again. If the problem persists, either the data in the file is corrupted, or your hardware is not working properly.
228 Backup cannot restore these files. The directory you are trying to restore to contains a file with the same name as a directory in your backup set. Try restoring to a different directory.
229 The path cannot be found. The path may have changed (for example, if Backup is trying to restore files to a deleted directory), or it is not available on the disk or tape currently in the drive. If this is a network path, the network may not be available.
230 A file with the same name already exists. Backup cannot overwrite this file, because you have chosen to disable this option in the Settings - Options dialog box.
231 The operating system cannot open another file. Close one or more files, and then try again. If the problem persists, quit Backup and all other running programs, restart Windows, and then try again.
232 You do not have the necessary access rights to write data to this location. For more information, contact your network administrator.
233 Directory full.
234 Backup has encountered a bad file handle. Quit and restart Backup, and then try again. If the problem persists, quit Backup and all other running programs, restart Windows, and then try again.
235 You do not have the necessary access rights to delete this file. The file may be write-protected. If this is a network file, contact your network administrator.
236 Backup was unable to find the necessary files. Quit and restart Backup, and then try again.
237 You do not have the necessary access rights to read from this location. For more information, contact your network administrator.
238 You do not have the necessary access rights to write to this location. For more information, contact your network administrator.
239 There is not enough disk space to continue this operation. Delete one or more files on the disk, and then try again.
240 Backup does not recognize the operating system you have specified for your source files.
241 Backup does not recognize the operating system you are trying to back up to.
242 Backup has encountered an error in the date and time. Quit and restart Backup, and then try again.
243 Backup has encountered a bad parameter. Quit and restart Backup, and then try again.
244 Backup has encountered an unexpected error number. Quit and restart Backup, and then try again.
245 Backup has encountered an unsupported function. Quit and restart Backup, and then try again.
246 Backup has encountered an invalid filename. Quit and restart Backup, and then try again.
247 Backup has encountered an unexpected or undefined message from the operating system. Quit and restart Backup, and then try again.
248 Backup has encountered an unknown file type. Quit and restart Backup, and then try again.
249 Backup cannot find this file. If this is a network file, the network may not be available. Or, the file Backup is looking for may have been deleted or moved.
250 Backup was unable to close a file properly. Quit and restart Backup, and then try again.
251 Backup has encountered an unexpected or undefined operating system error. Quit Backup and all other running programs, restart Windows, and then try again.
252 Backup cannot continue because too many files are open. Close any files that are not currently in use, and then try again.
253 You do not have the necessary access rights for this file. The file could be a hidden or read-only file. If this is a network file, contact your network administrator.
254 Backup has encountered an invalid operating system function number. Quit Backup and all other running programs, restart Windows, and then try again.
255 Backup has encountered a memory block error. Quit and restart Backup, and then try again.
256 Backup does not have enough free memory to run properly. Quit one or more programs, and then try again. If the problem persists, quit and restart Windows, and then restart Backup.
257 Backup is trying to use a memory block address that is already in use by another device. To resolve this conflict, look up 'If you have a hardware conflict' in the Troubleshooting section of the Windows Help Contents.
258 Backup has encountered an invalid environment error. Quit and restart Backup, and then try again.
259 Backup has encountered an invalid format error. Quit and restart Backup, and then try again.
260 Backup has encountered an invalid access code. Quit and restart Backup, and then try again.
261 Backup has encountered invalid data. Quit and restart Backup, and then try again.
262 Backup has encountered an unknown device. Quit and restart Backup, and then try again.
263 Backup has encountered an invalid disk drive. Quit and restart Backup, and then try again.
264 End of file.
265 There are no more files in the directory.
266 There are no more disk drives.
267 Backup has reached the end of extended attributes. Quit and restart Backup, and then try again.
268 Drive not ready.
269 Backup has encountered an unknown command. Quit and restart Backup, and then try again.
270 Backup was unable to read the files from the backup set correctly. Try running ScanDisk from the Windows Tools menu to determine whether there is an error on your hard or floppy disk. If the problem persists, the files cannot be retrieved.
271 Backup has encountered an invalid IDStructure length request. Quit and restart Backup, and then try again.
272 The tape format you are using is not supported by Backup.
273 Backup could not find the sector it needs to perform this operation. If you are using a disk, try running ScanDisk from the System Tools menu. If you are using a tape drive, retry the operation. If the problem persists, reformat the tape or use a different tape.
274 The printer is out of paper.
275 Backup could not write to this disk. Quit Backup and all other running programs, restart Windows, and then try again. If the problem persists, the disk may be corrupted.
276 Backup could not read from this disk. One or more of the files may be in use by another operation. Try again later, or quit other running programs, and then try again.
277 Backup has encountered a general failure error. Quit and restart Backup, and then try again.
278 A file is needed that is in use by another program. Quit all programs not currently needed, and then try again.
279 One or more needed files is in use by another program. Quit all running programs, and then try again.
280 A disk was removed while it was in use by Backup. Quit and restart Backup, and then try the operation again.
281 The sharing buffer has been exceeded. Quit and restart Backup, and then try again.
282 Backup has encountered an operating system reserved error. Quit and restart Backup, and then try again.
283 Backup has encountered an unsupported network request error. Quit and restart Backup, and then try again.
284 The network connection has been lost or the network is currently busy. Check your network connection, or try again later.
285 There is a duplicate name on the network. Try backing up to a different directory.
286 Backup could not find the specified network name. The network drive could be down. Try this operation again later.
287 The network resource you are trying to access is busy. Try again later.
288 The device you are trying to use no longer exists the on network. Specify a different device, and then try again.
289 The Net BIOS command limit has been exceeded. Quit and restart Backup, and then try again.
290 Backup has encountered an error in the network adapter hardware. To resolve a possible conflict, look up 'If you have a hardware conflict' in the Troubleshooting section of the Windows Help Contents.
291 Backup has encountered an incorrect response from the network. Quit and restart Backup, and then try again.
292 Backup has encountered an unexpected network error. Quit and restart Backup, and then try again.
293 Backup has encountered an incompatible remote adapter. Quit and restart Backup, and then try again.
294 The print queue is full. Wait until some files have printed, and then try again.
295 There is not enough room on your hard disk for this print file. Delete one or more files, and then try again.
296 Print file was deleted.
297 The network name Backup is looking for has been deleted.
298 You do not have the necessary network access rights to carry out this operation. For more information, contact your network administrator.
299 Backup has encountered an incorrect network device type. Quit and restart Backup, and then try again.
300 Backup could not find the specified network name. Quit and restart Backup, and then try again.
301 Backup has exceeded the network name limit. Quit and restart Backup, and then try again.
302 Backup has exceeded the Net BIOS session limit. Quit and restart Backup, and then try again.
303 Temporary pause.
304 The specified network request was not accepted. Quit and restart Backup, and then try again.
305 Print redirection has paused. There is a problem with the network drive. Try this operation again later.
306 Backup has encountered an operating system reserved error. Quit and restart Backup, and then try again.
307 Backup has encountered an operating system reserved error. Quit and restart Backup, and then try again.
308 Backup was unable to create a directory. If your hard disk is full, delete one or more files, and then try again.
309 Backup has encountered an interrupt 24 (critical error handler) failure. Quit and restart Backup, and then try again.
310 Backup has encountered too many redirections. Quit and restart Backup, and then try again.
311 Backup has encountered a duplicate redirection Quit and restart Backup, and then try again.
312 The password you typed is not valid. Try again.
313 Backup has encountered an invalid operating system parameter. Quit and restart Backup, and then try again.
314 Backup was unable to write to the network. Check your network connection, and then try again.
315 A path name is too long. You may be using a file system that is incompatible with Backup.
316 Backup was unable to find the specified location on the tape, which may be damaged. Retry the operation. If the problem persists, try reformatting the tape.
317 Backup has encountered an invalid extended data record for a file or directory. To try to correct the problem, run ScanDisk, which is located in the System Tools folder.
318 Backup has encountered extended file data that is incompatible with the current operating system. The incompatible data cannot be restored The rest of the data will be restored successfully.
319 Backup has encountered a serious error in Operation Manager. Quit Backup and all other running programs, restart Backup, and then try again.
320 Invalid drive referenced.
321 Backup cannot locate the specified tape drive. If you do have a tape drive, try redetecting the drive by double-clicking the 'Add New Hardware' icon in Control Panel, and then clicking 'Automatically detect installed hardware' on the second screen. If the problem persists, check the connections to the drive, or contact the hardware vendor.
322 Tape drive controller configuration failed.
323 Backup cannot communicate with the tape drive controller board. Try redetecting the drive by double-clicking the 'Add New Hardware' icon in Control Panel, and then clicking 'Automatically detect installed hardware' on the second screen. If the problem persists, check the connections to the drive, or contact the hardware vendor.
324 Your tape drive is attempting to use a resource that is already in use by another device. To resolve this conflict, look under Troubleshooting in the Windows Help Contents for the topic 'If you have a hardware conflict.'
325 Interrupt conflict detected.
326 Colorado Trakker hardware error.
327 Unable to detect a Colorado Trakker.
328 Colorado Trakker: Parallel port interrupt not available or in use.
329 Colorado Trakker: DMA buffer not available.
330 The drive is not ready. Make sure a tape is inserted in the drive, and that the drive door is closed, and then try again.
331 Insert a tape into the drive, and then try again.
332 Tape drive motor speed is not within tolerance.
333 A motor error has occurred in the tape drive. \nThe cause might be a jammed tape.
334 The tape drive motor is jammed or stalled.
335 The tape you are trying to back up to is write-protected.\nRemove the write protection and then try again, or try a different tape.
336 Tape drive error.
337 Backup has encountered an error in the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
338 Backup has encountered an illegal track on this tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
339 Backup has received an illegal command from the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
340 Illegal entry.
341 The current tape is broken or not wound tightly enough. Try rewinding it manually. If that doesn't work, try a different tape.
342 Backup has encountered an illegal cartridge reference command on this tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
343 Backup has encountered an error in the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
344 Backup has received an illegal command from the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
345 Backup has unexpectedly encountered the end of this tape. The data on this tape cannot be retrieved. The tape you are using is in a format that is incompatible with Backup.
346 Tape needs to be formatted.
347 Power failure to drive.
348 The tape drive's power connection is not working properly. \n\nPossible solutions: \n\n1. Make sure the drive is securely plugged into the port on your computer.\n2. Try a different power connector. \n3. Disconnect the power connection from another device, and then try again.
349 This tape drive has not been initialized. Try shutting down Microsoft Windows and turning your computer off and then back on.
350 Your tape drive is not working correctly.
351 Backup has encountered an error in the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
352 Backup has encountered a data segment that is too long. The data on this tape cannot be retrieved. The tape you are using is in a format that is incompatible with Backup.
353 Backup has encountered a sequencing error on the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
354 This tape is not compatible with the tape drive.
355 Backup cannot reference the tape drive. Clean the tape drive head, and then try again. If the problem persists, the data on the tape cannot be retrieved. You can reformat and reuse the tape.
356 Backup could not find the edge of the tape. Clean the tape drive head, and then try again. If the problem persists, the tape is damaged. Try a different tape.
357 Backup has encountered an error in the tape drive. Try shutting down Microsoft Windows and turning your computer off and then back on.
358 The tape in the drive has an invalid format. Try reformatting the tape. If that doesn't work, insert a different tape.
359 The current tape is broken. Insert a different tape, and then try again.
360 The data on this tape cannot be recovered because of a fault in the floppy disk controller.
361 Backup is unable to properly configure the tape drive data rate.
362 Format incomplete.
363 The format operation was not completed. Remove the tape from the tape drive, reinsert it, an then try again. If the problem persists, use a different tape.
364 Tape drive hardware error.
365 To ensure that your tape drive is installed correctly,\nrefer to the installation guide that came with the hardware.\nYou also try restarting your computer, and then restarting Backup.
366 Drive communication error.
367 Backup has encountered a drive communication error. This problem can occur if a tape is inserted while Backup is initializing, or if the tape is rewinding during initialization. Possible solutions:\n\n1. Wait for the software to reestablish communication with the drive.\n2. Remove the tape. When the 'No Tape' icon appears, reinsert the tape.\n3. Check all data cable connections, and then try the operation again.\n4. Try redetecting the drive by double-clicking the 'Add New Hardware' icon in Control Panel, and then clicking 'Automatically detect installed hardware' on the second screen.
368 Drive not ready.
369 Your disk controller is not compatible with Backup, or your computer does not support concurrent DMA mode.
370 The Backup Interrupt Manager received an invalid request. There is probably a conflict in your hardware I/O (input/output) resources. To solve this problem, look up 'If you have a hardware conflict' in the Troubleshooting section of the Windows Help Contents.
371 Backup has detected a new tape in the drive. The operation cannot continue. Restart Backup, insert the original tape, and then try again. Do not insert a new tape unless Backup prompts you to do so.
372 Backup did not detect a tape drive. If you do not have a tape drive, click OK. If you do have a tape drive, it is not working properly. Check the following, and then try again:\n
373 1. Make sure that all cables are installed correctly and all connections are secure.\n2. Make sure the tape drive is properly grounded.\n3. Reinstall Backup by double-clicking the Add/Remove Programs icon in Control Panel.
374 No controller board detected.
375 No tape in drive.
376 Backup could not detect a tape in the tape drive. If a tape is already inserted, remove it, reinsert it, and then try again.
377 Seek failed.
378 Backup cannot determine where the tape is positioned. The data on the tape cannot be recovered. You may be able to reuse this tape after you reformat it.
379 Backup has encountered a serious error in the Interrupt Manager. Quit Backup and all running programs, restart Backup, and then try again.
380 Backup does not support this tape format. Reformat the tape, and then try again.
381 This tape is either formatted incorrectly or is incompatible with Backup. Possible solutions:\n\n1. Consult your hardware guide to ensure that the tape is compatible with Backup.\n2. Remove the tape. When the 'No Tape' icon appears, reinsert the tape.\n3. Reformat the tape.\n4. Try a a different tape.
382 Recovering from previous tape-retry or tape-removed error.
383 End of tape encountered before the end of volume is reached.
384 There is another file or directory with the same name. Rename this file to avoid overwrite conflicts.
385 Warning: Tape needs to be formatted before operation can proceed.
386 Warning: Tape needs to be erased before operation can proceed.
387 Warning: Tape needs to be renamed before operation can proceed.
388 The tape was formatted successfully.
389 The tape was erased successfully.
390 The tape was renamed successfully.
391 The tape was unerased successfully.
392 Attempting tape error recovery.
393 Backup has found a bad sector on this tape, so some of its data has been relocated. You can continue to use the tape and its data as you normally would.
394 You have canceled all subsequent operations.
395 The network device you are trying to connect to is unavailable. Try again later.
396 Warning: This operation has been canceled by the system.
397 You have canceled this operation.
398 Error: A tape was removed during this operation.
399 Error: The file comparison failed. Files in the backup set and in the source are different.
400 Error: A specified disk directory was not found during the compare operation.
401 Error: The file header in this backup set is corrupted or missing. Reformat the tape. If the backup set is from a local hard drive run scandisk to make sure that there are no problems with your hard disk.
402 Error: The file size in the header of this tape is corrupted. Reformat the tape.
403 Error: The path size in in the header of this tape is corrupted. Reformat the tape.
404 Error: The file size on disk has changed since the operation started. Select the files again, and then retry the operation.
405 Backup cannot read the data in this file. Quit and restart Backup, and then try again. If the problem persists, the file is probably corrupted and the information in it cannot be recovered.
406 Backup cannot restore the data from this file. Quit and restart Backup, and then try again. If the problem persists, the file is probably corrupted and the information in it cannot be recovered.
407 Backup cannot compare the data in this file. Quit and restart Backup, and then try again. If the problem persists, the file is probably corrupted and the information in it cannot be recovered.
408 Begin auto-compare of file(s).
409 Begin reset of file archive bit.
410 Beginning to delete file(s).
411 Operation continued on this tape.
412 Beginning to add this tape volume to the library.
413 Beginning to delete tape information in the library.
414 Beginning to rename this tape in the library.
415 Beginning to update this erased tape in the library.
416 Backup could not find the virtual device driver named QIC117.VXD that it needs to run. Reinstall Backup, and then try again. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
417 Backup could not find a file it needs to run. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
418 Not enough memory available.
419 There is not enough memory available to run Backup. Quit one or more programs, and then try again. If that doesn't work, shut down and restart Microsoft Windows, and then start Backup.
420 Invalid Error. Quit and restart Backup, and then try again.
421 Backup could not find the correct device driver. Quit Backup and all other running programs, restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
422 Backup cannot continue because data was written to the floppy disk by another program before the backup operation was completed. Start the operation again.
423 The tape is full. Please insert the next tape.
424 Backup was unable to read from the disk or network drive. Quit and restart Backup, and then try again.
425 Backup was unable to write to the disk or network drive. If you are using a disk, make sure it is not write-protected, or use a different disk. If you are using a network drive, verify your connection, and then try again.
426 Backup cannot find the specified data on the disk or network. The data may be corrupted. Quit and restart Backup, and then try again. If the problem persists, the data cannot be retrieved.
427 Backup was not able to get the drive information it needs. Quit and restart Backup, and then try again.
428 You do not have the necessary access rights to write to this network device. For more information, contact your network administrator.
429 Backup has encountered an error in the kernel driver interface. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
430 Incompatible driver(s) in SYSTEM.INI
431 Backup has encountered an error in the kernel driver interface. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
432 Backup has detected an error with the Colorado Trakker. Quit and restart Backup, and then try again.
433 Backup was unable to transfer data properly. Retry the operation.
434 Backup has detected an error with the Colorado Trakker. Quit and restart Backup, and then try again.
435 Backup was unable to detect a Colorado Trakker. Quit and restart Backup, and then try again.
436 The parallel port that the Colorado Trakker needs to use is not available. Quit all running programs, and then try again. If the problem persists, quit Backup and all other running programs, restart your computer, and then try again.
437 The DMA buffer that the Colorado Trakker needs to use is not available. Quit all running programs, and then try again. If the problem persists, quit Backup and all other running programs, restart your computer, and then try again.
438 Backup has encountered a driver time-out error. Quit Backup, shut down Windows, and then turn off your computer's power for at least 30 seconds. Restart Windows and Backup, and then try again.
439 Backup was unable to detect a tape drive because the driver VFBACKUP is not installed.
440 VFBACKUP was not installed because there are one or more incompatible driver(s) in your SYSTEM.INI file. Open your SYSTEM.INI file, and then delete the following drivers (or any other backup device drivers), if found: VFINTD.386, VITD.386, CBWTAPE.386, CMSDTAPE.386, FASTBACK.386, CPBVXD.386.
441 Do you want to halt this operation?
442 Colorado Backup
443 Backup
444 %s kilobytes
445 Back up:
446 Backup set: %s
447 %s of %s kilobytes backed up.
448 Backup operation complete.
449 %s of %s files backed up.
450 Backup of volume "
451 Preparing backup operation.
452 Preparing compare operation.
453 Preparing erase operation.
454 Preparing format operation.
455 Preparing restore operation.
456 Kilobytes selected
457 Date/time operation canceled:
458 If you cancel this operation, some files may not be selected. Are you sure you want to cancel?
459 Backup is unable to start this operation and is shutting down. Restart Backup, and then try again.
460 Compare
461 %s of %s kilobytes compared.
462 Compare operation complete.
463 %s of %s files compared.
464 Compare of volume "
465 Backup was unable to save your hardware configuration correctly. Quit Backup and all other running programs, restart Backup, and then try again.
466 - Make sure your Trakker tape drive is connected correctly. - Make sure the parallel port interrupt does not conflict with another hardware device. For more information, see Windows Help or your tape drive documentation. If the problem persists, reinstall Backup, and then try again. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
467 Created
468 Backup could not the insert the list view column - Created. Quit Backup and all other running programs, restart Backup, and then try again.
469 The disk you are trying to back up to is write-protected.\nRemove the write protection and try again, or try a different disk.
470 Quit and restart Backup, and then try again.
471 Date/time operation completed:
472 \nAre you sure you want to continue?
473 Unknown error.
474 Type a different volume name, and then try again.
475 This volume name is already in use.
476 Elapsed time: %s
477 Please enter a valid MS-DOS filename with no extension.
478 Erase
479 Erase operation complete.
480 Do you really want to erase this tape?
481 Erase of tape
482 Errors encountered: %ld
483 Errors occurred during this operation. Do you want to view them now?
484 Total number of errors encountered:
485 Error/warnings during operation:
486 Error reading tape
487 Files selected:
488 File set: %s
489 Backup was unable to write a total system backup file set. Possible causes:\n\n1. The backup tape you are using is full or damaged.\n2. Network access rights are restricted.\n3. The tape drive is not functioning properly.\n4. The tape you are using is formatted incorrectly or is in a format that is incompatible with Backup.\n5. There is not enough space on your hard disk.\n\nIf none of these is the cause, quit and restart Backup, and then try again.
490 The data in this file set cannot be read. Either the file set is in a format that Backup doesn't recognize, or the data is corrupted.
491 The file named "%s" already exists.\nDo you want to overwrite it with the backed-up file dated %s?
492 Backup does not support backing up from one floppy onto itself or onto another floppy.
493 Backup does not support drag and drop for .QIC files.
494 This filename is not valid. \nThe file must have the extension .FST.
495 Format
496 Format operation complete.
497 Format of tape
498 Warning: Tape formatting may fail if your computer is in heavy use. If your tape does not format successfully after several attempts, it may not be possible to format the tape.
499 ", from disk
500 ", from tape
501 Backup cannot create a file on the device you want to back up to.\nMake sure you specify a valid name for the device, and that you have the necessary network access rights, and then try again. For more information, contact your network administrator.
502 Backup cannot write to the device you want to back up to. Possible causes:\n\n1. The device is write-protected.\n2. Network access rights are restricted.\n3. The device is full.\n4. An invalid device name is specified.\n\nIf none of these is the cause, select a different destination device.
503 Warning: You are modifying a full system backup set.\nDo you want to continue?
504 Backup was unable to configure your hardware correctly. Quit Backup and all other running programs, restart Backup, and then try again.
505 Backup was unable to configure your hardware correctly. Quit Backup and all other running programs, restart Backup, and then try again.
506 You can use any character except \, /, :, and >. \nEnter a valid filename.
507 This filename is not valid.
508 Backup could not create an image list. Quit Backup and all other running programs, restart Backup, and then try again.
509 This tape is in a format that is incompatible with Backup.\nInsert a different tape, and then try again.
510 Please insert a disk.
511 This disk is not formatted.\nInsert a formatted disk, and then try again.
512 This tape is not formatted.\nInsert a formatted tape, and then try again.
513 Please insert the tape "%s".
514 Please enter a name of at least one character.
515 Passwords do not match. Please reenter your password.
516 Backup has experienced an internal communication failure. Quit Backup and all other running programs, restart Backup, and then try again.
517 Modified
518 Backup could not the insert the list view column - Modified. Quit Backup and all other running programs, restart Backup, and then try again.
519 Name
520 Backup could not insert the list view column - Name. Quit Backup and all other running programs, restart Backup, and then try again.
521 Please insert the next disk.
522 Please insert the next tape.
523 The password you entered does not match. \nPlease reenter the password.
524 Backup could not find any files for this operation. Either the specified files or directory no longer exist, you do not have the necessary network access rights, or none of the selected files need to be backed up. This operation has been canceled.
525 Now backing up the files you selected.
526 Now comparing the files you selected.
527 Now erasing tape.
528 Now formatting tape.
529 Now resetting archive flag to True for backed up files.
530 Now restoring the files you selected.
531 This disk already contains data. Do you want to erase it?\nIf you want to erase this disk, click Yes. If you do not want to erase this disk, insert a blank disk, and then click No.
532 This tape already contains data.\nDo you want to erase it? If you want to erase this tape, click Yes. If you do not want to erase this tape, insert a blank tape, and then click No.
533 No disk was detected. \nInsert a formatted disk into the drive, and then try again.
534 No tape was detected.\nInsert a tape into the drive, and then try again.
535 Backup did not detect a tape drive. If you do not have a tape drive, click OK, and then select a different backup medium. If you have a tape drive, try redetecting it by double-clicking the 'Add New Hardware' icon in Control Panel, and then clicking 'Automatically detect installed hardware' on the second screen.
536 Drop one .FST file onto Backup
537 An operating system error has occurred. \nQuit Backup and all other running programs, restart Windows, and then try again.
538 Operation:
539 Operation has been halted.
540 Operation complete.
541 Print:
542 You must quit Backup before you restart Windows.\nTo quit Backup and save your current file set, click OK. Otherwise, click Cancel.
543 This program is in the middle of an operation. \nTo avoid damaging your data, quit Backup and all other running programs, and then restart Windows from the Start menu.
544 Try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
545 Some component of Backup is corrupt or missing.
546 Reset archive flags
547 %s of %s kilobytes processed.
548 Reset archive bit operation complete.
549 %s of %s files reset.
550 Restore
551 Restore:
552 %s of %s kilobytes restored.
553 Restore operation complete.
554 %s of %s files restored.
555 Restore of volume "
556 Size
557 Backup could not insert the list view column - Size. Quit Backup and all other running programs, restart Backup, and then try again.
558 You must specify a backup destination before you can save the file set.\nClick "Next Step", and then choose a destination.
559 Date/time operation started:
560 Quit Backup and all other running programs, restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
561 A serious error has occurred in Backup.
562 Backup
563 Compare
564 General
565 Restore
566 Tape drive error
567 Tape %s - %s\n
568 Backup cannot write to this tape. The tape may be damaged, or it may be in a format that Backup does not support. Reformat this tape, or try a different tape.
569 Tape not formatted
570 Untitled tape
571 The tape drive and floppy disk controller are sharing a system resource. To use the tape drive, you must first cancel any selections of files on floppy disks.
572 Tape selection error.\nBackup was unable to communicate with the tape drive. Quit Backup and all other running programs, restart Backup, and then try again.
573 This tape is not formatted.\nDo you want to format the tape?
574 The tape you are trying to back up to is write-protected.\nMove the write tab to the record position, and then try again.
575 An unknown or unexpected task was opened. \nQuit Backup and all other running programs, restart Backup, and then try again.
576 This task is unknown.
577 Backup was unable to create a thread to complete this operation. Quit Backup and all other running programs, restart Backup, and then try again.
578 to disk.
579 to tape.
580 Type
581 Backup could not the insert the list view column - Type. Quit Backup and all other running programs, restart Backup, and then try again.
582 Backup has encountered an unknown or unexpected message. Quit Backup and all other running programs, restart Backup, and then try again.
583 Bad or unknown message.
584 Backup has received an unknown Operation Manager message. Quit Backup and all other running programs, restart Backup, and then try again.
585 Untitled
586 Please insert volume "%s" disk number %d.
587 Volume "%s" was not found.\nPlease insert the disk that contains this volume.
588 Please insert volume "%s" tape "%s" number %d.
589 Please insert volume "%s" tape "%s".
590 Waiting for tape
591 Write-protected.
592 File
593 File
594 Folder
595 %s, Page: %d
596 Start Backup
597 What to back up:
598 Where to back up:
599 Start Restore
600 Restore from:
601 Files to restore:
602 Start Compare
603 Compare from:
604 Files to compare:
605 Next Step >
606 Could not load the AVI resource
607 File filtering - folders
608 Go to
609 Select location for redirected files
610 OK
611 Cancel
612 Your registry has been successfully restored. You MUST restart your computer now or it may not work properly.
613 There may have been an error restoring the registry. Your computer may not work properly. If it doesn't, try tagging the windows directory and restoring the files again.
614 There was an error saving the registry. Full system backup will not work properly. Try the operation again.
615 Contents of "%s"
616 The tape that this directory is from has been removed. Please re-insert the tape and try again from the previous screen.
617 You have selected an invalid destination.\nPlease select a valid device or directory.
618 Please insert volume "%s" tape number %d.
619 Unable to proceed.\nWaiting for tape.
620 Backup is unable to access the currently selected volume. If you are trying to access a floppy disk volume, make sure that your floppy disk is in the floppy drive and then press the F5 key to refresh the list.
621 This volume contains long names and Windows was installed\nwithout long name support. In order to use this volume you must enable\nlong name support in Windows.
622 This volume belongs to a linked set.\nPlease place the first volume into the drive.
623 Unrecoverable bad sector error on tape. If the problem persists, try reformatting your tape.
624 Full System Backup
625 fullbkup
626 File Set
627 Unable to refresh.\nWaiting for tape.
628 Backup has encountered an invalid media type. The format of the tape you are using is not compatible with your tape drive.
629 Not Identified - Generic
630 Generic - CMS drive
631 QIC40 drive
632 QIC80 drive
633 QIC3010 drive
634 QIC3020 drive
635 Developed by Colorado Memory Systems
636 a division of Hewlett-Packard Company
637 Error aquiring the parallel port.
638 Backup cannot communicate with a Colorado Trakker if the parallel port it is using is currently being accessed by another device, such as a printer. Do not attempt to print and backup simultaneously with the same port.
639 Settings - Options
640 Tape Properties
641 Backup does not understand the format of the data on this tape. To restore data from this tape, use the application that was used to put the data onto this tape.
642 Backup cannot read this vendor specific backup set. To restore data from this backup set, use the application that was used to write it. Adding backup sets to this tape may corrupt existing vendor specific backup sets.
643 From drive
644 An attempt to restore a file failed because the disk file is newer than the file being restored.
645 Sun
646 Mon
647 Tue
648 Wed
649 Thu
650 Fri
651 Sat
652 Backup is not able to redirect more than one source drive at a time.
653 Retension
654 Retension operation complete.
655 Now retensioning tape.
656 Preparing retension operation.
657 Rename
658 Rename operation complete.
659 Now renaming tape.
660 Preparing rename operation.
661 Secure Erase
662 Secure Erase operation complete.
663 Now secure erasing tape.
664 Preparing secure erase operation.
665 Unerase
666 Unerase operation complete.
667 Now unerasing tape.
668 Preparing unerase operation.
669 Do you really want to retension this tape?
670 Do you really want to rename this tape?
671 Warning : All data will be lost. Do you really want to secure erase this tape?
672 Do you really want to unerase this tape?
673 QIC80 wide drive
674 The parallel port your Tape Drive is connected to is configured as an ECP, Enhanced, or Bi-Directional port. Using your Tape Drive with this configuration will not work reliably and you will not be able to recover data from tapes. To use your Tape Drive without data loss on this port, the port configuration must be changed to NON-ECP mode.
675 Please contact your PC manufacturer for specific information on how to do this as the required steps vary widely across different PC manufacturers.
676 You cannot select a floppy destination when using a volume from tape.\nPlease select another non floppy destination.
677 Floppy Controller
678 FC-10
679 FC-20
680 Parallel Port
681 TC-15
682 SCSI Controller
683 Unavailable
684 One or more fields of the date you have entered is invalid, please recheck the date fields.
685 Modified Backup
686 modbkup
687 and
688 This volume contains system settings (System Registry), restore these settings.
689 Unable to start backup because the backup application, %s, is currently running, and only one backup may run at a time.
690 Microsoft Backup
691 A fatal write error has been encountered.
693 Backup could not find a file it needs to run. Quit and restart Backup, and then try again. If the problem persists, try reinstalling Backup. To reinstall Backup, look up 'Add/Remove Programs' in the Windows Help Index.
694 Wrong version of SCSIBK32.DLL
695 Internal hardware failure
696 Unrecognized SCSI Device
697 Internal hardware failure
698 Tape Full
699 No tape
700 Encountered invalid segment on tape
701 New tape in drive detected.
702 Tape is empty
703 Media is not compatible in this tape drive
704 A fatal read error has been encountered.
705 A FATAL read error has been encountered.\nThis problem may have been caused by a dirty drive head. Use a cleaning cartridge to clean the drive head and then try the operation again. WARNING: Some tape drives cannot be cleaned. Consult the hardware manual for your drive for cleaning instructions. If the problem persists, then use a different tape cartridge
